LENZ LI-USB DRIVER FOR MAC DOWNLOAD

The Roco LocoMaus 2 Roco Part number has been shown to support operating equipment on a layout running trains and throwing switches as well as programming locomotives on the programming track. The following table tries to show which systems support these three feature groups. For programming in service mode, the LocoMaus 2 appears to only be able to write to CV’s. If you have either ZTC system and wish to add computer control to your layout, an XPA and Hayes Compatible Modem may be a more cost effective solution than one of the purpose built interfaces. Check the site status page.

Uploader: Gasida
Date Added: 4 May 2013
File Size: 28.12 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 16060
Price: Free* [*Free Regsitration Required]

The Compact is not available in North America. System specific limitations are also expressed lenz li-usb the Limitations section of each system below.

Lenz LI-USB Ethernet PC Interface | Tony’s Train Exchange

Viessmann has indicated the Commander’s built in USB port can only li-uzb used for updating the firmware lenz li-usb sending lenz li-usb to the commander, not for operating the device. This includes the LI-Server, which may be running in the background. Roco calls their XpressNet implementation “RocoNet”. Any adapter s present will reply with their NetBios name, which can then be selected.

Lenz USA – LI-USB

It is unknown at this point in time if we can control either an Elite or a Select using one of the other interfaces. The device drivers for Windows are included on lenz li-usb CD that comes with the device and from the Hornby Website. For programming in service mode, the LocoMaus 2 appears to only be able to write to CV’s. There are some instructions for creating that cable in the LZV manual. lenz li-usb

You May Also Need:  BROADCOM USH W SWIPE SENSOR DRIVER

Lenz LI-USB Ethernet PC Interface

This system uses the Lenz XpressNet Phone Adapter and a Hayes Compatible modem to provide control of locomotives and stationary decoders. The Roco MultiMaus Roco Part number has been shown to support operating equipment on a layout running trains and throwing switches and programming locomotives in both service and li-hsb mode. The Compact is the same device as the Atlas Commander, and has lenz li-usb same restrictions as the commander. XpressNet lenz li-usb a Command Bus developed by Lenz and used by: We have developed an alternative method for connecting to an XpressNet based system which should prove to be lenz li-usb cost effective on XpressNet based systems that do not support programming or feedback via the Li-ussb, LIF, or LIF computer interfaces, or for those who are interested in experimenting with computer control, but don’t need all the features supported lenz li-usb the Lenz interfaces.

Hardware Limitations Connecting with: This device does not require an XpressNet connection. Additional information on copyright, trademarks and licenses is linked here.

The BlackBox is a standalone decoder programmer. The following tools are available from the XpressNet menu when this connection is active click lenz li-usb the name to read more on each tool:. This feedback comes through the use of S88 compatible lenz li-usb modules. Check the site status page.

The XpressNet protocol allows the DCC manufacturers that use it to select what functionality they wish to provide in their command stations. This functionality ranges lenz li-usb oenz all features” to “bare bones minimal”.

You May Also Need:  HP 1006P DRIVER DOWNLOAD

You can’t program lenz li-usb from a computer with Set It may be necessary to build an adapter to plug an XpressNet accessory into a Command Station from another manufacturer. In general, the features that JMRI cares about can be grouped into three areas: The XpressNet specification available lenz li-usb the Lenz website specifies the electrical communications standards and command set needed for devices to li-jsb with the command station.

The lenz li-usb table tries to show which systems support these three feature groups. We may add XBus Version 1. If you li-uusb to use an XPA and a Hayes Lenz li-usb Modem to control your XpressNet based system, you will be limited to control of locomotives and accessory decoders.

Connecting the Li-USB-Ethernet to JMRI Decoder Pro 3

Paco Canada also provides two methods for lenz li-usb feedback to non-feedback equipped systems. If you have installed the Lenz software, make sure none of it is running.

The onboard serial interface of the ZTC is not supported lenz li-usb this point in time. We should be able to use this to connect using one of the supported XpressNet computer interfaces, but the limitations of this li-ub have not been lenz li-usb.